top of page
Ez2cy yacht enclosure images (2).png

Hard Acrylic • Impact Modified

About EZ2CY®  The Clearest Boat Enclosures You Can See the Difference​

92% Light Transmittance (ASTM D1003)   |   0.2% Initial Haze   |   10,000 lbs Tensile Strength (ASTM D638)   |   5-Year Prorated Warranty   |   35+ Years in Business

Mystery of the Enclosures

Confused by the huge number of enclosure products on the market? Then this page is for you. There are many materials available and in use in the enclosure industry, and each has its own pros and cons. If the enclosure best suited for your current application is not EZ2CY®, being honest with you now will enable us to be a consideration on your future vessels.

Introduction

This information is an attempt to untangle the confusing, confounding, and often costly mystery of the various clear products used in the making of enclosures for the boating world. Many would prefer that this all stay a mystery. However, EZ2CY® is dedicated to serving the boating public with honesty and integrity. It is our belief that giving the consumer information so they can make an informed choice is the ethical and proper path for all companies.
Not every boat or owner is a candidate for any particular enclosure. Making the right choice is in everyone's best interest. To achieve that, you need clear information — and clearing the mystery is exactly what we aim to do here.

What Are the Different Products?

It may at first seem a simple task to explain the different materials; however, the different materials go by many different trade names and are not always clearly identified. The following covers each category: acrylic, polycarbonate, clear vinyl (Isinglass), and co-polyester.

Who We Are An Honest Manufacturer in a Confusing Market

EZ2CY® was founded on a single conviction: boaters deserve the truth about what they're buying. From our facility in Riviera Beach, Florida, we have manufactured precision boat enclosures for over 35 years  serving recreational boaters, charter captains, and luxury yacht owners across the U.S. coastline and beyond.

Every enclosure we ship is fabricated from Acrylite® Plus impact-modified acrylic, chosen because it consistently outperforms every alternative across every metric that matters at sea: clarity, UV stability, tensile strength, and long-term dimensional integrity.

We are not the enclosure for every vessel. We say so  upfront  because we would rather send you to the right product today than lose your trust for your next, more suitable vessel. That honesty has earned us repeat business for three decades. After installation, we back every enclosure with a 5-year prorated warranty that guarantees light transmittance will not degrade more than 3% in five years  a standard virtually no competitor publishes.

A Word About UV

Recently some companies have implied that their product will protect the public from more of the harmful ultraviolet radiation than the competition's product does. One company suggests that the rainbow effect seen when looking through its product with polarized sunglasses indicates that a special coating is protecting you. This just is not the case.

⚠️ UV Claims — What the Data Actually Shows
Fact 1: All of the products on the market filter out approximately the same amount of harmful UV radiation.

Fact 2: The rainbow (birefringence) effect is a property of uncoated polycarbonate itself not a protective coating. Look through uncoated polycarbonate with the same polarized lenses and you will see the same rainbow.

A Word About UV

Recently some companies have implied that their product will protect the public from more of the harmful ultraviolet radiation than the competition's product does. One company suggests that the rainbow effect seen when looking through its product with polarized sunglasses indicates that a special coating is protecting you. This just is not the case.

* Acrylic cannot be sewn through at any thickness. EZ2CY® uses proprietary track and mechanical fastening methods specifically engineered for Acrylite® Plus panels.

Acrylic

Acrylic is made from transparent thermoplastic resins formed by polymerizing esters of acrylic acid or methacrylic acid. Acrylic is the clearest of the products used for enclosures  in fact clearer than normal window glass. Acrylic cannot be sewn through, no matter what thickness. Therefore, conventional sewing-based construction methods cannot be used.

Brand names include but are not limited to: Acrylite®, PLEXIGLAS®, LUCITE®, Plaskolite®.

Modified Acrylics

Modified acrylics contain an additive that imparts special properties making them more break-resistant. These properties also make them slightly more susceptible to scratching and slightly higher haze than conventional acrylic. Modified acrylics include IMPLEX®, DURAPLEX®, and others. Acrylite Plus® is a modified acrylic that has overcome the deficiencies of earlier modified products and is now the standard used in all EZ2CY® enclosures.

Coated Acrylics

Coated acrylics have a surface treatment that makes them more scratch-resistant. However, scratches that do occur cannot be buffed out of coated products. One of the most widely known coated acrylics is LUCITE® SAR.

UV Resistance of Acrylic

Acrylics are inherently resistant to UV without requiring any coating. Acrylite® carries a manufacturer's warranty stating it will not change by more than 3% light transmittance or 3 points on the yellow index in ten years. Acrylics are also resistant to many chemicals found around boats, including diesel oil/smoke and turpentine.

 

The One Limitation — and How We Address It
 

Acrylic's notable downfall is break-ability when bent beyond its limit (typically during improper opening or closing). However, a tensile strength of 10,000 lbs in the closed (in-use) position is greater than any other enclosure material discussed herein, excluding vinyl which simply stretches.

In the application of a boat enclosure this limitation is easily avoided by learning proper handling procedures. Acrylite® Plus has substantially reduced this problem and is now used in all EZ2CY® enclosures.

Polycarbonates

Polycarbonates are a class of resins that are thermoplastic, tough, transparent, and nontoxic. Polycarbonate is not as clear as acrylics and exhibits a rainbow (birefringence) effect of colors when viewed from various angles. This effect is amplified by polarized sunglasses and is particularly troublesome when trying to spot feeding billfish or floating debris.

Brand names include but are not limited to: LEXAN®, Cyrolon®, HYZOD®, Crystal-Flex®, Aqua-Lite®.

Polycarbonate Durability vs. Clarity Trade-Off

Polycarbonates are tough — they tend to dent rather than break when struck with a hard object. In thicknesses more than .080", the object is even more likely to bounce off without denting. However, contrary to what some believe, polycarbonate is softer than acrylic. This makes it more susceptible to scratching and harder to compound scratches out.

Polycarbonates are subject to UV degradation to a much greater degree than acrylic. Uncoated polycarbonate can change as much as 7% light transmittance in 60 months of South Florida sun (GE TM 90-12 data). Haze in those same months reached 55.7% and the yellowing index reached 13.5. Polycarbonates are also attacked by diesel oil/smoke and turpentine.

 

Sewing Thin-Gauge Polycarbonate

Thin forms (.020, .030) can be sewn easily. Thicker gauges (.060) can be sewn, but not practically. Like acrylic, polycarbonates are notch-sensitive — a notch on the edge can cause the sheet to tear readily, much like paper. The thin gauges are practical on sailboat dodgers where the area is small and the panel is regularly covered when not in use. On large applications, thin polycarbonate tends to rattle like a tin sheet, and rolling it causes severe scratching. A rolling or improper opening can result in a permanent dimple.

 

Thicker Polycarbonates (Architectural Grades)

HYZOD® SL is a UV-inhibited polycarbonate that starts with 86% light transmittance and is warranted not to change more than 5% in five years (yellowing index increase limited to 5 in the same period).

HYZOD® AR is a UV-inhibited polycarbonate with a scratch-resistant coating. However, it is designed for flat architectural glazing only and should not be exposed to the flexing and stresses of a boat enclosure, which would cause coating delamination. Once coatings are scratched, they cannot be repaired. Both products carry manufacturer warranties limited to flat architectural glazing — coverage that explicitly excludes the boat enclosure environment.

Clear Vinyl (Isinglass)

Almost everyone in the industry knows about clear vinyl, but very few know much about it. Because this guide is targeted at higher-end products, we discuss .040 pressed/polished vinyl and omit .020 and .030 rolled goods.
Clear Vinyl (a.k.a. ISINGLASS®) is clear PVC with plasticizer to make it flexible. The .040 pressed/polished sheet is formed by pressing two pieces of .020 vinyl with highly polished surfaces under great pressure and heat. This product was regarded as premium until the 1990s.
 
Vinyl Performance Data
.040 pressed/polished vinyl begins with a light transmittance of approximately 84%, haze of about 1.4%, and a yellow index of -3.3 (the negative value is attributed to a slight blue cast, visible when looking through the vinyl's edge).
Vinyl is not a dimensionally stable product — it expands and contracts significantly with temperature changes. A tight enclosure on a cold morning may show wrinkles and sagging on a warm afternoon. After 5,000 hours of Xenon Arc UV testing, vinyl haze rises to 18.8% and the yellow index reaches 3.3. By comparison, acrylic at the same 5,000-hour point transmits 92.1% of light, haze is 4.8%, and the yellow index is just 0.5.
 
Coated Vinyl (Strataglass®)
Strataglass® introduced coated vinyl in 1993. The coating makes it more scratch-resistant than even acrylic. However, once scratched, repairs cannot be made. Tests have shown that coatings have not been able to stop UV-driven haze development. After more than 25 years in the business, EZ2CY® cannot visually distinguish coated from uncoated vinyl once both have been weathered.

Important: Either vinyl product, when rolled up while moist, will fog out and require substantial time stretched in the sun before clearing. Where possible, it is better to tab/snap the vinyl open without rolling.

Co-Polyesters (PETG)

A relative newcomer to the marine market, co-polyesters are most commonly associated with plastic soda bottles. Semi-rigid sheets are made from raw PETG pellets produced by Eastman® Chemical under the name SPECTAR® — a glycol-modified form of PET. Trademarked sheet brands include VIVAK®, Ultros®, Rexstar® HG, Prime® PETG 5700, and TOUGH STUFF®.
Only UV-resistant grades should be used outdoors, as unprotected co-polyester breaks down very rapidly in sunlight. VIVAK® UV starts with 86% light transmittance and 1.0% haze — better than vinyl but still far from acrylic's 0.2%. Tensile strength at 7,800 lbs is the lowest of all semi-rigid materials. The most important practical limitation: co-polyester has a heat resistance of only 140°F. A four-sided enclosed bridge enclosure can easily reach this temperature, leading to warping and panel failure.

Choices — What's Right for Your Boat

Each of the materials listed has its place. Some owners don't care about ultimate clarity; some want only the best; some boats make a rigid enclosure impractical; some only need the enclosure for limited use; others may want to air-condition the bridge. There are 80-foot yachts where customers are shocked at acrylic pricing and end up with .020 roll goods. We believe that most high-end customers can tell whether their fabricator is well-informed — and it always pays to be honest.

Weigh each factor one at a time, then as a whole. We feel acrylic performs very well and have not yet found another material that would serve us or our customers as proficiently. We have seen charter boats where the acrylic still looks and functions very well after ten years. However, we are constantly looking, testing, and scrutinising all available materials to ensure EZ2CY® remains the most advanced and clearest enclosure available.

Material Selection Guide

•       Small sailboat dodger with regular rollup use → thin-gauge polycarbonate is practical and cost-effective

•       Budget-constrained application → .040 pressed vinyl is a reasonable mid-grade choice

•       Large flybridge, pilothouse, or luxury yacht → acrylic is the measurable performance leader in every category

•       Enclosed four-sided bridge in warm climates → avoid co-polyester (140°F heat limit)

•       Any application where long-term clarity and UV stability are the priority → EZ2CY® Acrylite® Plus acrylic

Quality — The Weakest Link

When fabricating a high-end enclosure there is a need to ensure all components are high-end. A Viking Yacht owner would never accept zinc-plated cleats on his yacht — and he should not have to accept auto carpet binding or cotton thread on his enclosure. As one moves to a better glazing material, a parallel move must be made to the best components. The use of Valmex® Nautica fabric, SolarFix® thread, and YKK® zippers creates a total premium product. Boat owners who understand quality appreciate every detail.

 

Installation — Execution Matters

Equally important is the execution and fabrication of all components. The enclosure needs to fit the vessel and the owner. Most of us would not purchase an expensive suit without a proper lining — and you should not accept an enclosure made by simply cutting a hole for the window and leaving raw fabric edges exposed to the elements to unravel and look unsightly.

A fine enclosure — like a fine suit — should have all edges turned and finished. Improper installation of even the finest enclosure can lead to premature failure and excessive leaking. Snaps should be placed closely together, or better yet, a track-to-track installation completed to distribute stress evenly and minimise gaps where water may enter.

 

Conclusion

The answer for most boats is likely a combination of clear materials. An important factor in this equation is how long the product will deliver quality and performance that is acceptable to you and meets your high standards. Only you can determine the weight of that factor.

We sincerely hope any misconceptions have been clarified and that this information enables you to make a more informed decision. If you have a question, please contact us below.

Explore More at EZ2CY.com

The following pages on our website provide additional information to support your decision:

Riviera Beach, FL • Stuart to Miami

Let's talk about your boat.

Tell us your vessel and how you use it. We'll walk you through the right system and schedule a measurement aboard.

Subscribe Form

Thanks for submitting!

EZ2CY® Inc

1500 Australian Avenue # 4 Riviera Beach,Fl,33404

1-800-448-4317

  • Facebook
  • LinkedIn

©2023 by EZ2CY® . 

EZ2CY®, Inc. purchased from MAL-MAK CORP. various assets in 2008. JEFF SMITH has no involvement with the operation of EZ2CY®, Inc

bottom of page